ConCar Variable Speed Belts 22x8 - 600 Li

ConCar Variable Speed Belts 22x8 – 600 mm inner length – DIN 7719 / ISO 1604

The ConCar Variable Speed Belts 22x8 with an inner length of 600 mm is a variator belt compliant with DIN 7719 and ISO 1604, designed for continuous operation in continuously variable speed drives (CVTs). Unlike a conventional V-belt, which runs on a fixed diameter, a Variable Speed Belts must provide consistent traction across the entire adjustment range of the pulleys. To achieve this, it is significantly wider than it is tall and has a shallower flank angle, ensuring that the wedge effect remains uniform across the entire radial path and preventing the belt from binding or slipping at the end positions.

This length in the drive

The inner length of 600 mm is a short version for the 22x8 profile. This means a compact center distance and a correspondingly small drive volume, but at the same time a high bending frequency. At a belt speed of 20 m/s, this equates to approximately 31.2 revolutions per second. With short belts, check whether the tapered pulleys meet the minimum running diameter specified by the manufacturer, as the bending stress has the greatest impact on service life at this point.

For design and comparison with an existing belt, the three length specifications are important because manufacturers use different reference dimensions. The inner length (Li) is 600 mm; it is measured at the inner circumference of the belt and is the standard ordering dimension in Germany. The effective length (Ld) of 640 mm refers to the neutral axis and is the dimension used in many catalogs and drive calculations. The outer length (La) of 650 mm is measured at the back of the belt. With a profile height of 8 mm, the difference between the inner and outer lengths is 50 mm, which corresponds to twice the difference in circumference across the belt height. When replacing an old belt, always compare using the same reference dimension; otherwise, you can easily be off by several centimeters.

Dimensions and specifications

• Internal length (Li): 600 mm

• Effective length (Ld): 640 mm

• External length (La): 650 mm

• Profile: 22x8 according to DIN 7719 / ISO 1604

• Top width: 22 mm

• Height: 8 mm

• Flank angle: 25°

• Construction: open-sided, toothed

• Mixture: Chloroprene (CR)

• Tensioning material: Polyester cord

• Antistatic: yes, according to ISO 9563

• Temperature range: -30 °C to +80 °C

• Belt speed: up to 30 m/s

• Weight: 0.096 kg

• Article number: G422080600

• EAN: 4059213020585

• Manufacturer: ConCar

Structure and materials

The belt consists of a chloroprene rubber core with a longitudinally inserted polyester cord as a tensile member. The flanks are open, meaning they are not covered with fabric. This noticeably increases the coefficient of friction on the pulley and thus improves the transmissible torque, but in return requires clean, unworn pulley flanks. The compound is antistatically conductive according to ISO 9563, which allows the belt to be used in dusty areas and in ATEX-relevant environments.

The 25° flank angle is the crucial difference compared to a conventional V-belt, which operates at 34 to 40 degrees. The shallower angle generates less wedging effect per millimeter of radial travel, ensuring smooth belt operation across the entire pulley adjustment range and preventing binding at the end positions. Simultaneously, the large upper width of 22 mm provides the necessary contact area to transmit torque solely through friction. The toothed underside reduces bending stiffness to such an extent that the belt can operate even on small effective diameters without the flanks overheating due to internal flexing.

Typical areas of application

Belts of this size are typically found in compact drives: bench drills and small lathes with continuously variable spindle speed, feed drives on band and circular saws, laboratory centrifuges and shakers, dosing and small conveyors in packaging lines, as well as garden equipment and small drives where the installation space does not allow for large pulleys.

What these applications have in common is that the rotational speed must be adjusted during operation to suit the material, batch, or demand. A Variable Speed Belts solves this problem purely mechanically, without any electronics in the drive train. This is advantageous wherever dust, moisture, vibration, or temperature would damage a frequency converter, and it remains the only economical solution for existing machines because the variator is an integral part of the machine's design.

Assembly and tension

Before ordering, check the adjustment range of your drive. The belt must be able to be fitted without force, whether the pulleys are fully closed or open. After fitting, tension the belt to the tension specified by the machine manufacturer and check again after the break-in period. If several belts run in parallel in one drive, they must always be replaced as a complete set, as a new belt, in addition to worn ones, bears the entire load.

Transverse cracks on the underside indicate an insufficient bearing diameter or cold brittleness, while longitudinal cracks and frayed edges point to misalignment between the pulleys. It's worthwhile checking the alignment with a ruler or laser when changing the belt, as even a few millimeters of misalignment over a one-meter center-to-center distance can halve the belt's lifespan.

Similar names for other brands

Variable Speed Belts are standardized according to DIN 7719 and ISO 1604. A belt with a 22x8 profile and a 600 mm inner length is therefore dimensionally identical regardless of the manufacturer; no modification of the pulleys is required for replacement. This ConCar belt replaces, among others:

• OPTIBELT: VB 22x8 / VARIO POWER 22x8

• GATES: Multi-Speed ​​22x8 / Predator V Variable Speed

• CONTITECH: VARIO Speed ​​22x8 / CONTI-V VARISPEED

• MEGADYNE: VARISECT 22x8

• MITSUBOSHI: VARI-SPEED 22x8

• BANDO: Variable Speed ​​22x8

• PIX: Variable Speed ​​22x8

Delivery

The belt is supplied as a single, endless belt. Standard lengths and common profiles are available from stock; custom lengths and widths are available upon request. If you are unsure which length your drive requires, please send us the part number of your old belt or the dimensions of your pulleys, and we will check the compatibility.