ConCar Variable Speed Belts 41x13 - 970 Li

ConCar Variable Speed Belts 41x13 – 970 mm inner length – DIN 7719 / ISO 1604

The ConCar Variable Speed Belts with a 41x13 profile and a 970 mm inner length, is an open-flanked, molded-tooth variator belt conforming to DIN 7719 and ISO 1604. It transmits drive power exclusively via its two flanks, moving radially on the conical, axially displaceable pulley halves during operation. This movement is precisely the principle of a mechanical speed converter: when one pulley closes, it pushes the belt outwards to a larger effective diameter, while on the opposite side it slides inwards. This allows the transmission ratio to change continuously without the need for shifting, clutching, or electronic control.

This length in the drive

With an inner length of 970 mm, this belt belongs to the short end of the 41x13 profile. Short belts rotate significantly more often at the same belt speed: at 20 m/s, this belt completes approximately 19.4 rotations per second, each with two complete bending cycles. Therefore, the service life of short belts is almost always limited by the number of bending cycles and not by the tensile load. In such drives, pay particular attention to the smallest effective diameter and ensure that the tension is no higher than necessary.

For design and comparison with an existing belt, the three length specifications are important because manufacturers use different reference dimensions. The inner length (Li) is 970 mm; it is measured at the inner circumference of the belt and is the standard ordering dimension in Germany. The effective length (Ld) of 1,030 mm refers to the neutral axis and is the dimension used in many catalogs and drive calculations. The outer length (La) of 1,052 mm is measured at the back of the belt. With a profile height of 13 mm, the difference between the inner and outer lengths is 82 mm, which corresponds to twice the difference in circumference across the belt height. When replacing an old belt, always compare using the same reference dimension; otherwise, you can easily be off by several centimeters.

Dimensions and specifications

• Internal length (Li): 970 mm

• Effective length (Ld): 1,030 mm

• External length (La): 1,052 mm

• Profile: 41x13 according to DIN 7719 / ISO 1604

• Top width: 41 mm

• Height: 13 mm

• Flank angle: 27°

• Construction: open-sided, toothed

• Mixture: Chloroprene (CR)

• Tensioning material: Polyester cord

• Antistatic: yes, according to ISO 9563

• Temperature range: -30 °C to +80 °C

• Belt speed: up to 30 m/s

• Weight: 0.673 kg

• Article number: G441130970

• EAN: 4059213023333

• Manufacturer: ConCar

Structure and materials

The belt consists of a chloroprene rubber core with a longitudinally inserted polyester cord as a tensile member. The flanks are open, meaning they are not covered with fabric. This noticeably increases the coefficient of friction on the pulley and thus improves the transmissible torque, but in return requires clean, unworn pulley flanks. The compound is antistatically conductive according to ISO 9563, which allows the belt to be used in dusty areas and in ATEX-relevant environments.

The 27° flank angle is the crucial difference compared to a conventional V-belt, which operates at 34 to 40 degrees. The shallower angle generates less wedging effect per millimeter of radial travel, allowing the belt to run smoothly across the entire adjustment range of the pulleys and preventing binding at the end positions. Simultaneously, the large upper width of 41 mm provides the necessary contact area to transmit torque solely through friction. The shaped toothed underside reduces bending stiffness to such an extent that the belt can operate even on small effective diameters without the flanks overheating due to internal flexing.

Typical areas of application

Belts of this size cover the classic field of industrial variators: feed and grinding belt control in woodworking machines, demand-controlled piston and screw compressors, spinning and drawing units in textile machines, industrial mixers and kneaders with soft start, take-off and screw drives on plastic extruders, as well as boring mills and lathes with stepless control.

What these applications have in common is that the rotational speed must be adjusted during operation to suit the material, batch, or demand. A Variable Speed Belts solves this problem purely mechanically, without any electronics in the drive train. This is advantageous wherever dust, moisture, vibration, or temperature would damage a frequency converter, and it remains the only economical solution for existing machines because the variator is an integral part of the machine's design.

Assembly and tension

Before ordering, check the adjustment range of your drive. The belt must be able to be fitted without force, whether the pulleys are fully closed or open. After fitting, tension the belt to the tension specified by the machine manufacturer and check again after the break-in period. If several belts run in parallel in one drive, they must always be replaced as a complete set, as a new belt, in addition to worn ones, bears the entire load.

Before you classify a belt as worn, it's worth taking a look at the pulley. A worn groove allows the belt to sink deeper, causing it to sit on the bottom of the groove and lose contact with the belt flanks. This manifests as a sudden loss of power, even with a seemingly new belt. This can be checked in a minute using a groove feeler gauge.

Similar names for other brands

Variable Speed Belts are standardized according to DIN 7719 and ISO 1604. A belt with a 41x13 profile and a 970 mm inner length is therefore dimensionally identical regardless of the manufacturer; no modification of the pulleys is required for replacement. This ConCar belt replaces, among others:

• OPTIBELT: VB 41x13 / VARIO POWER 41x13

• GATES: Multi-Speed ​​41x13 / Predator V Variable Speed

• CONTITECH: VARIO Speed ​​41x13 / CONTI-V VARISPEED

• MEGADYNE: VARISECT 41x13

• MITSUBOSHI: VARI-SPEED 41x13

• BANDO: Variable Speed ​​41x13

• PIX: Variable Speed ​​41x13

Delivery

The belt is supplied as a single, endless belt. Standard lengths and common profiles are available from stock; custom lengths and widths are available upon request. If you are unsure which length your drive requires, please send us the part number of your old belt or the dimensions of your pulleys, and we will check the compatibility.