ConCar Variable Speed Belts 47x13 - 850 Li

ConCar Variable Speed Belts 47x13 – 850 mm inner length – DIN 7719 / ISO 1604

The ConCar Variable Speed Belts 47x13 with an inner length of 850 mm is a variator belt compliant with DIN 7719 and ISO 1604, designed for continuous operation in continuously variable speed drives (CVTs). Unlike a conventional V-belt, which runs on a fixed diameter, a Variable Speed Belts must provide consistent traction across the entire adjustment range of the pulleys. To achieve this, it is significantly wider than it is tall and has a shallower flank angle, ensuring that the wedge effect remains uniform across the entire radial path and preventing the belt from binding or slipping at the end positions.

This length in the drive

With an inner length of 850 mm, this belt belongs to the short end of the 47x13 profile. Short belts complete significantly more revolutions at the same belt speed: at 20 m/s, this belt completes approximately 22.0 revolutions per second, each with two complete bending cycles. Therefore, the service life of short belts is almost always limited by the number of bending cycles and not by the tensile load. In such drives, pay particular attention to the smallest effective diameter and ensure that the tension is no higher than necessary.

For design and comparison with an existing belt, the three length specifications are important because manufacturers use different reference dimensions. The inner length (Li) is 850 mm; it is measured at the inner circumference of the belt and is the standard ordering dimension in Germany. The effective length (Ld) of 910 mm refers to the neutral axis and is the dimension used in many catalogs and drive calculations. The outer length (La) of 932 mm is measured at the back of the belt. With a profile height of 13 mm, the difference between the inner and outer lengths is 82 mm, which corresponds to twice the difference in circumference across the belt height. When replacing an old belt, always compare using the same reference dimension; otherwise, you can easily be off by several centimeters.

Dimensions and specifications

• Internal length (Li): 850 mm

• Effective length (Ld): 910 mm

• External length (La): 932 mm

• Profile: 47x13 according to DIN 7719 / ISO 1604

• Top width: 47 mm

• Height: 13 mm

• Flank angle: 28°

• Construction: open-sided, toothed

• Mixture: Chloroprene (CR)

• Tensioning material: Polyester cord

• Antistatic: yes, according to ISO 9563

• Temperature range: -30 °C to +80 °C

• Belt speed: up to 30 m/s

• Weight: 0.667 kg

• Article number: G447130850

• EAN: 4059213023739

• Manufacturer: ConCar

Structure and materials

The belt consists of a chloroprene blend (CR) with an embedded polyester tensile cord. Chloroprene was deliberately chosen here: it is resistant to oil mist, ozone, UV radiation, and weathering, and retains its elasticity in a temperature range of approximately -30 to +80 degrees Celsius. The polyester cord absorbs the tensile forces and keeps elongation low over the belt's lifespan, which is particularly important in a variator because an elongated belt length directly translates into a shift in the control range.

The 28° flank angle is the crucial difference compared to a conventional V-belt, which operates at 34 to 40 degrees. The shallower angle generates less wedging effect per millimeter of radial travel, allowing the belt to run smoothly across the entire adjustment range of the pulleys and preventing binding at the end positions. Simultaneously, the large upper width of 47 mm provides the necessary contact area to transmit torque solely through friction. The shaped toothed underside reduces bending stiffness to such an extent that the belt can operate even on small effective diameters without the flanks overheating due to internal flexing.

Typical areas of application

Belts of this size are used in heavy-duty drives: threshing and drum drives on combine harvesters, intake and chopping units on forage harvesters, sawing and chipboard plants, large conveying and crushing plants, as well as compressor and blower drives where the speed must follow the demand without shifting a gearbox.

What these applications have in common is that the rotational speed must be adjusted during operation to suit the material, batch, or demand. A Variable Speed Belts solves this problem purely mechanically, without any electronics in the drive train. This is advantageous wherever dust, moisture, vibration, or temperature would damage a frequency converter, and it remains the only economical solution for existing machines because the variator is an integral part of the machine's design.

Assembly and tension

Variable Speed Belts are supplied as continuous, single belts and cannot be shortened or joined. Before installation, the tapered pulleys must be fully opened so that the belt can be positioned at its smallest effective diameter. Tensioning is then achieved via the pulley's adjustment range or the motor rocker arm. Prying the belt open by the pulley edge is particularly damaging with Variable Speed Belts , as this can damage the exposed flanks and the tension member without any visible external damage.

Before you classify a belt as worn, it's worth taking a look at the pulley. A worn groove allows the belt to sink deeper, causing it to sit on the bottom of the groove and lose contact with the belt flanks. This manifests as a sudden loss of power, even with a seemingly new belt. This can be checked in a minute using a groove feeler gauge.

Similar names for other brands

Variable Speed Belts are standardized according to DIN 7719 and ISO 1604. A belt with a 47x13 profile and an 850 mm inner length is therefore dimensionally identical regardless of the manufacturer; no modification of the pulleys is required for replacement. This ConCar belt replaces, among others:

• OPTIBELT: VB 47x13 / VARIO POWER 47x13

• GATES: Multi-Speed ​​47x13 / Predator V Variable Speed

• CONTITECH: VARIO Speed ​​47x13 / CONTI-V VARISPEED

• MEGADYNE: VARISECT 47x13

• MITSUBOSHI: VARI-SPEED 47x13

• BANDO: Variable Speed ​​47x13

• PIX: Variable Speed ​​47x13

Delivery

The belt is supplied as a single, endless belt. Standard lengths and common profiles are available from stock; custom lengths and widths are available upon request. If you are unsure which length your drive requires, please send us the part number of your old belt or the dimensions of your pulleys, and we will check the compatibility.