V-ribbed belt PK 1460

V-ribbed belt PK 1460 - Ribbed belt

All belts with the PK profile can be delivered from stock or factory in Germany within a few days.

Spacing between ribs (profile PK): 3.56 mm

V-ribbed belts are made of rubber with fiberglass reinforcement.
Standard widths: 1-50 ribs (more available on request).

If you have any questions about our Poly-V tapes, please contact our staff to discuss the product, prices and delivery times.

Dimensions:

Outer length (La): 1460 mm;
Rib width: 3.56 mm;
Minimum pulley diameter: 45 mm
; Height: 4.5 mm;
Profile: K / PK;
Maximum speed: 60 m/s;
Standards: RMA IP-26, ISO 9982, DIN 7867

The PK/K profile multi-ribbed belt is made of rubber with fiberglass reinforcement.

Advantages of V-ribbed belts

Even distribution of the workload across the entire belt width.
Compact, efficient, and low-vibration drive system.
Small pulley diameters.
No lubrication required.
Quiet operation.
Long service life.
Easy installation.
Speeds up to 60 m/s are possible.
To reduce costs, guide pulleys without rails can be used.
Complex drive configurations, such as serpentine or helical drives, can be designed due to the belt's high flexibility.

Temperature range: -25 to +100 °C.
Performance can be improved by increasing the number of ribs.
Rubber poly-V belts have antistatic properties according to ISO 1813.
Manufactured according to RMA IP-26, ISO 9982, and DIN 7867.
Oil and heat resistant.
Antistatic properties.

General product description

Multi-ribbed belts (also known as poly-V belts) are endless, friction-fit drive belts with multiple parallel longitudinal ribs. They combine the advantages of flat and V-belts: On the underside, trapezoidal rubber ribs act as a frictional link against correspondingly shaped pulleys. The PK profile is a metric design according to DIN 7868 and is characterized by a very low belt height. With a rib spacing of only 3.56 mm per rib (corresponding to a width of 3.56 mm), a PK multi-ribbed belt is particularly narrow and flexible. This slim design allows for use on very small pulley diameters. Typically, the closed belt blank is vulcanized from an elastomer rubber compound (e.g., neoprene/NR-SBR or EPDM), with a low-stretch polyester tensile cord incorporated into the belt body. This creates a homogeneous belt structure in which the top and bottom rubber layers, as well as the backing layer, are firmly bonded together. The many narrow ribs allow the force to be transmitted over a large contact area, enabling space-saving, smoothly running drives with high power density.

Technical specifications

The PK profile conforms to DIN 7868 and has the following characteristic dimensions: rib spacing (pitch) 3.56 mm and belt height approximately 4.5 mm. The belt width is calculated by multiplying the number of ribs by 3.56 mm. PK V-ribbed belts are manufactured in customer-specific widths – the number of ribs can be freely selected depending on the performance requirements (typically a few to several dozen ribs). The belt is made of abrasion-resistant rubber (often neoprene/SBR or EPDM), which offers good wear resistance and elasticity. The tensile cord is made of high-quality polyester fabric with very low elongation. This material combination gives the belt high tensile strength and a long service life.

Operating conditions typically range from approximately -30 °C to +80 °C, with standard compounds retaining their mechanical properties within this temperature range. Higher temperatures accelerate the aging of the rubber compound. Like other V-belts, PK ribbed belts have limited oil resistance, so contact with strong mineral oils should be avoided. A conductive layer is often applied to the rubber backing to dissipate static electricity.

The belt's performance is primarily determined by the number of ribs and the material used. The low-elongation reinforcement ensures minimal changes in length under load, while the parallel ribs provide a large contact area – both contributing to high efficiency and smooth running. Special compounds and aramid-reinforced belts are also available for specific requirements (e.g., very high temperatures or oil-resistant versions).

Care and assembly instructions

PK multi-ribbed belts are generally low-maintenance, but should be installed and cared for correctly. Before installation, ensure that the pulleys are clean, free of burrs, and properly aligned. Place the belt loosely into the appropriate grooves without twisting it; the tension can usually be adjusted by moving the driven shaft or using tensioning devices. Overtensioning should be avoided, as this can shorten the belt's lifespan. After installation, it is recommended to check the tension again after a break-in period.

During operation, contaminants such as abrasion particles or oil deposits should be regularly removed from the belt. Caution is advised with oils and greases: due to their limited oil resistance, contact with oily substances can attack and embrittle the rubber. Defective belts (e.g., with cracks in the ribs or torn rubber) should be replaced immediately, as all belts in a set should always be replaced together in multi-belt applications. With proper installation and maintenance, PK V-ribbed belts offer a long service life and reliable operation